I’m going to do another typography tutorial today. This time it will be number 6 from the list. This is another one that is quite simple to do, yet produces a really neat effect. The original is called Create Smokey Typography in 12 Steps written by Tom over at PSDFan.com.
Okay so to start off, we’re going to need some images of smoke. I found the following on flickr.com searching their Creative Commons by-nc-sa section, which is a fantastic resource.
I opened all these photo’s in the GIMP and desaturated them and inverted their colors as necessary so that the smoke is white and the background is black. Minimize those windows or otherwise set them aside for later.
Open a new document, black background 600×125 pixels.
Next add some text to your document. Any font will do. I chose a bold sans font.
Now, duplicate your text layer, select the original text layer and click Filters > Blur> Motion blur… In the motion blur dialog, select Linear for the type, make the length 20 and the angle 90.
Now, this will only blur in one direction, so it will have the effect of moving your blurred text upward. Select the move tool (M) and use your arrow keys to move the active layer down until it lines up the way you want. Also, lower the layer opacity to 60%.
Now, bring up one of your smoke images. You can either use your selection tools to select an area of the smoke or just select all and copy and paste the smoke into a new layer in your image. Once you’ve got the layer anchored, set its Mode to Difference.
Now, take a soft fuzzy eraser at low opacity and erase around the edges of the smoke until you can’t see the hard edges of your selection. You might even want to reduce the opacity of the layer a bit.
Now just keep repeating the previous technique with different smoke images until you have something that looks good.
Now, paste in one more smoke layer and set the layer mode to Multiply. Use your eraser to erase some of the layer so you can see the smoke and letters again.
Now, select the text layer that we did not blur earlier. It should be higher in the stack than the blurred layer. Right-click the layer and click “Layer to image size”. This will set the layer boundry to the same size as the rest of the image. Select the Smudge tool (S). Select the Circle Fuzzy (19) brush, Scale 1.00 and rate 50. Using small circular motions, smudge those letters until they look more smokey.
I chose not to do the last part where he did random brush strokes on the page. It seemed very out of place to me, and not everyone is going to have a drawing tablet and pen. However if you want to do that, you can get into the brush dynamics by selecting the paintbrush tool and clicking the plus sign next to Brush Dynamics.
That’s it. I hope you enjoyed the tutorial and maybe learned something new.
Update: Here’s the XCF file if you want it. psdfan_tut.zip
I’m adapting one of the tutorials mentioned in the previous post. It’s from PSDFan and it’s titled Create a Simple, Professional Typographical Design. As noted, this is a simple effect, but produces a very nice design which could be used for a wallpaper, logo, or maybe a business card.
Open a new document whatever size you like with a black background. I’m going with 1400 x 900.
In order to make the next part a little easier, I maximized my image window so I can see the gray area around the border. Now, select the text tool by pressing T, change the color to 323131, and drag a text box completely around the image. Type in whatever text you want using all caps, and copy/paste it over and over until it fills the screen.
Now, select the rotate tool by pressing Shift+R. In the rotate dialog box, enter -25 for the angle and click the Rotate button. Mine still ended up being a little small, so I selected the Scale tool by pressing Shift+T and stretched it a little until it covered the entire canvas.
Now, create a new layer and select the text tool again. Set the color to white and the size to 250, or whatever makes it the right size for your image. Input your text, then rotate the layer -25 degrees just like above. Use the Move tool (M) to position the text in the center of the page.
Set the text layer to Soft light, and duplicate it in order to make it stand out more. Adjust the opacity of the duplicated layer until you have something you like.
Now, select the Gradient tool (L). Set your foreground color to white and background color to black. Set the gradient tool mode to Normal and the shape to Radial. Create a new layer and set its mode to Soft light. Click and drag the gradient from the center of the page to the top edge of the layer boundary. Adjust the layer opacity until you have something you like. I lowered it to about 77%. You should now have something like this.
That’s it! I hope you enjoyed this simple tutorial.
Today I’m going to teach you a method I use to fake a fill flash. The objective is to lighten the dark areas without blowing out the highlights. Here’s the before and after:
After four months of hard work we are proud to announce another release of the user manual. It features:
- documentation for GIMP 2.4
- new content, spelling and grammar fixes for English, German, French, Russian, Italian, Norwegian and Spanish
- an alternate CSS stylesheet for HTML
The source files of gimp-help-2.4.0 can be downloaded from ftp.gimp.org. Users should wait until this release has been packaged in a pre-compiled form that is easier to install. Find more information about our goals and how you can help at http://docs.gimp.org.
Three weeks later enough bug-fixes have piled up to warrant another bug-fix release in the stable GIMP 2.4 series. Please see the NEWS file for details.
GIMP 2.4.1. has been released to fix a few bugs. Here’s the release from gimp.org:
GIMP 2.4.1 is a bug-fix release in the stable 2.4 series. It fixes problems that were discovered after the 2.4.0 release. Please see the NEWS file for details.
It’s here, it’s here! For those of you who waited for the stable release, it’s now available. Head on over to gimp.org and download away. They changed their website design too, so when you get there and it doesn’t look familiar, don’t panic.
Update: Several readers have suggested easier and more effective methods. Check the comments section!
EPS is the vector graphic file format Adobe Illustrator saves in. Supposedly you can import these files directly to Inkscape if you have skencil and pstoedit installed, but I couldn’t make it work. So I converted it manually using the GIMP and Inkscape. Here’s how I did it.